Understanding Plumbing Basics is Vital for Bathtub Installation
Understanding Plumbing Basics is Vital for Bathtub Installation
Blog Article
The content in the next paragraphs relating to A Step-by-Step Guide to Installing a Bathtub is quite engaging. You should see for yourself.
Installing a bath tub isn't precisely rocket science, yet it does require solid plumbing, carpentry, and sometimes, tiling skills. Replacing an old bathtub with a new one is also a moderately tough project. If the old tub is readily obtainable, the task can move rapidly; if you need to open a wall surface to remove the old tub as well as place the brand-new tub, the job is much harder. In either instance, the task is within a home handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually qualified yourself for the work as well as fit trying it. Rather than hiring a contractor to take control of a halfway-completed project, it is better to take into consideration employing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will help you set up a new bath tub in your shower room if you have currently bought a new bathtub and also don't require to change the arrangement of your previous supply of water pipelines.
Your devices as well as product checklist should make up the following:
Getting ready for the Installment
First of all, the supporting frame provided with the bath needs to be fitted (if needed) according to the maker's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to ensure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets unit to avoid stress on the bathtub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you utilize all of the provided washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last position.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be quite bothersome because of the limited access that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the staying water that will come from the pipelines. As soon as the supply pipelines have actually been eliminated, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the needed position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 small points.
The following goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level and also changing the feet on the bathtub up until the spirit level reviews level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the appropriate supply pipeline by making a compression join; after that do the very same for the other tap.
Turn on the water supply and check all joints and brand-new pipework for leakages and tighten them if required. Fill the bathtub as well as likewise examine the overflow outlet as well as the regular electrical outlet for leakages.
Lastly, repair the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub must wait up until the tub has been used a minimum of once as this will settle it into its final setting.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin ensuring that the washers remain in place between the tap and also the sink. Protect the tap in position with the supplier supplied backnut. When the tap is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet adapters. The previous type should be connected to the faucet finishes initially, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to break an inflexible seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, leading to complications with moisture as well as possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, as well as can securing voids up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to enable the movement experienced when the bathtub is in use. The sealant can crack relatively early if you do not think about this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the market. It is suggested to fit the floor tiles making use of waterproof or waterproof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been made aware of that article on How to Install a Bathtub from an associate on our other website. Sharing is good. Helping people is fun. Many thanks for your time. Don't forget to check up our website back soon.
Achieve peace of mind. Report this page